Be-Friend Technology
new open                                                                                
Emulator,Development System
Development Kit
Programmer,Interface Protection
Basic Equipment
IC Components
USB SIMLAB 8051 Development Kit
1.ISP online burning programs can burn through a USB port to program MCS51 the 8K Flash ROM, up to the maximum burning program...
ARM9 BF-S3C2440 嵌入式發展系統

Development Kit > CME-564 Development Board 發展系統
  CME-564 Development Board 發展系統

The CME-564 (MPC564EVB) is a development system for the Motorola MPC564 PowerPC
microcontroller. The system provides for development of target applications for the similar MPC561,
MPC562, or MPC563 microcontrollers also. The system is Plug and Play with the supplied Debug
Monitor firmware in the on-board flash memory. Other features include 512K Byte (128K x 32)
Synchronous SRAM development or application memory, 2M Byte (512K x 32) Synchronous FLASH,
RS232, CAN and Ethernet Communication Interfaces, Keypad and LCD Module support, and the
Power Oak regulated supply source. The kit provides Serial Cable, Ethernet Cable, Universal Wall
Plug power source, printed hardware manual, and the MPC5xx support CD with programming utilities,
example software, support software, and technical manuals. Note: Due to limitations of peripherals
attached to the MPC564 bus ports this board should not be applied for single-chip mode application
support, see the CMD-564 version for this type application.


Memory Devices:
512K Byte (128K x 32) Sync. SRAM, optional additional 512K Byte
2M Byte (512K x 32) Sync. FLASH
512K Byte FLASH internal to MPC564 device
32K Byte SRAM internal to MPC564 device
POWER OAK (PC33394 P2.6) regulated power supply for 5V, 3.3V and 2.6V supplies.
MAP Switch – provides easy assignment of chip selects and memory mapping.
CONFIG Switch – Basic necessary Reset Word Configuration options.
COM1 - SCIA1 w/ RS232 type DB9-S Connection
COM2 - SCIA2 w/ RS232 type DB9-S Connection, TX / RX polarity option.
CAN Ports – 3 CAN transceiver interfaced ports, 1 x 4 headers.
10/100T Ethernet Port – LAN91C111 based MAC+PHY, memory mapped.
DEVELOPMENT Ports – Nexus 50 pin and dual voltage BDM Ports.
LCD Port - LCD Module Interface Connector w/ Contrast Adjust, Buffered and Memory Mapped
KEYPAD Port - 16 Key passive interface, applies QADC_B channels for operation.
BUS Port – 32 data and 24 address lines on 60 pin header.
CONTROL Port - Bus Controls with 40 pin header.
QSM Port – Serial I/O ports with 16 pin socket headers.
MIOS Port - MDA, PWM, and MGPIO ports with 34 pin socket header.
TPU Ports - 2 Timing Processor I/O ports with 20 pin socket headers.
QADC Ports - 2 Analog I/O ports, one 20 pin and one 24 pin socket header.
IRQ Port – Interrupt or MPC564 port I/O with 10 pin socket header.
POWER Port – Primary and standby power supply access port, no header.
I/O Connectors in .1 grid, pin headers for bus and control provide easy ribbon cable connection
 for external connections. Socket headers provide easy wire connection to breadboard prototype
area with 22ga solid wire.
Large Prototyping Area with +5V and ground connection grids.
Mictor Logic Probe connectors for the Address and Data bus (Not installed default)
Breadboard Prototyping area (2.5 x 1.5 inch) for easy installation of test connections.
System Indicators – Reset Indicator, Supply voltage indications for 5V, 3.3V, and 2.6V supplies
Reset Switches – POR, Hard, Soft Reset buttons.
User Components – 4 user indicators, 4 user Switches, 1 user Pot with socket header for I/O


Clock 56 MHz Maximum, 4Mhz reference
Operating temperature 0°C to +70°C
Power requirement 6 – 26V DC, 12VDC @ 300 ma Typical
Power output 5.8V @ 1.5A output with 5V, 3.3V, and 2.6V regulated supplies
Board Size 7.00 x 7.60 inches, 8 layers


AboutBest ChoiceNew ProductsNewsQ & AContact UsCourseDownload
Copyright All rights reserved. © Be-Friend Technology Inc. TEL:886-4-26528352 FAX:886-4-26523150
ADDRESS:43449 1F., No.8, Ln. 133, Yuandong St., Longjing Dist., Taichung City 434, Taiwan (R.O.C.)

My status